Trailblazer
1CC Aspirant
Hi, ik wil een loom bestellen bij FrancoB (AO) en hij vraagt nu om de specificaties vd kabel. Ik heb even gekeken maar weet zo niet welke specs ik moet kiezen ivm de NNC. Heeft iemand wellicht een idee?
Dit moet ik kiezen:
Video:
Power:
Audio:
Kick pinout:
En dit zijn de opties:
Controls:
Two 12 Pin AMP UPs wired for joystick, start and five buttons from the JAMMA edge.
One 10 pin AMP UP kick harness/extension for buttons four, five and six. In the CP buttons four and five will be linked to the 12 Pin AMP Ups. The end in the base can either be wired for CPS2/3 kick housing or a NAC style 10 pin AMP up.
Kick harness:
The 10/15 pin AMP UP kick harness connector of the Naomi seems to be wired to one of two pin outs. One is the typical 'UK Naomi' pin out and the other matches the Blast/Astro pinout. The NNCs seem to be wired to the Blast/Astro pin out.
I can wire the kick harness to suit your cab/control panel but I need to know how yours has been wired.
If you are already using a kick harness from a 1L6B or 2L12B panel, take a look at the 10 posistion AMP UP connector and see which of these two it matches (ignoring the colours):
Video:
Two main options:
a) Video wired to a HD15 breakout socket for VGA cable connection to Toshiba PF and Sanwa PFX
b) Video wired to a 5pin JST V connector for connecting to a CGA>VGA scaler
MS9 style 15pin AMP UP connections or PF/PFX 8 pin AMP UP connectors would also be possible
Audio:
Two main options again:
a) Audio wired to two high quality RCA plugs with a built in attenuation circuit to bring the audio to line level. These can then be plugged into the Sega amplifier and volume can then be controlled using the pot in the service board in the control panel.
b) Audio wired to two 2 pin AMP Ups to connect the output directly to the Naomi speakers. Volume would be controlled from the PCB.
Power:
Once again, two options:
a) 5v, 12v and GND wired to an 8pin AMP UP for connecting to the Sun ATX PSU
b) -5v, 5v, 12v and GND wired to ring terminals for connecting to a JAMMA PSU
Alvast erg bedankt!!
Dit moet ik kiezen:
Video:
Power:
Audio:
Kick pinout:
En dit zijn de opties:
Controls:
Two 12 Pin AMP UPs wired for joystick, start and five buttons from the JAMMA edge.
One 10 pin AMP UP kick harness/extension for buttons four, five and six. In the CP buttons four and five will be linked to the 12 Pin AMP Ups. The end in the base can either be wired for CPS2/3 kick housing or a NAC style 10 pin AMP up.
Kick harness:
The 10/15 pin AMP UP kick harness connector of the Naomi seems to be wired to one of two pin outs. One is the typical 'UK Naomi' pin out and the other matches the Blast/Astro pinout. The NNCs seem to be wired to the Blast/Astro pin out.
I can wire the kick harness to suit your cab/control panel but I need to know how yours has been wired.
If you are already using a kick harness from a 1L6B or 2L12B panel, take a look at the 10 posistion AMP UP connector and see which of these two it matches (ignoring the colours):
Video:
Two main options:
a) Video wired to a HD15 breakout socket for VGA cable connection to Toshiba PF and Sanwa PFX
b) Video wired to a 5pin JST V connector for connecting to a CGA>VGA scaler
MS9 style 15pin AMP UP connections or PF/PFX 8 pin AMP UP connectors would also be possible
Audio:
Two main options again:
a) Audio wired to two high quality RCA plugs with a built in attenuation circuit to bring the audio to line level. These can then be plugged into the Sega amplifier and volume can then be controlled using the pot in the service board in the control panel.
b) Audio wired to two 2 pin AMP Ups to connect the output directly to the Naomi speakers. Volume would be controlled from the PCB.
Power:
Once again, two options:
a) 5v, 12v and GND wired to an 8pin AMP UP for connecting to the Sun ATX PSU
b) -5v, 5v, 12v and GND wired to ring terminals for connecting to a JAMMA PSU
Alvast erg bedankt!!
